LinkBack Thread Tools
post #1 of 8 (permalink) Old 10-11-2009, 09:20 AM Thread Starter
Junior Member
 
Join Date: Oct 2009
Location: Pioneer, Louisiana, USA
Posts: 4
Post imported post

Hey guys,



Anyone have any details on the installation of Kuryakyn Handlebar riser kit for the wing kit # 7437?



I've got the front panel up and loose, but now...the speaker wire connectors under the rubber boot are giving me a fit to pull out. Is their a tab that must be pressed down on this connector...Haven't found this yet. Any advice out there?
Ridgeman is offline  
Sponsored Links
Advertisement
 
post #2 of 8 (permalink) Old 10-11-2009, 09:41 AM
Senior Member
 
SMEDEN(=the blacksmith)'s Avatar
 
Join Date: Sep 2009
Location: vordingborg, , Denmark
Model: GL1000 1975 K1+GL1800 2006 airbag(US-model).
Posts: 1,128
Post imported post

the lock tab sits in the connector on the side facing away the magnet of the speaker.

it is in the midle sektion of the connector , and protected by two raised plastic parts of the connector , one on each side of the lock tab. the lock tab has to be pressed in.

The winner is the man with most tools !
SMEDEN(=the blacksmith) is online now  
post #3 of 8 (permalink) Old 10-11-2009, 09:42 AM
Senior Member
 
OnaWingAndaPrayer's Avatar
 
Join Date: Nov 2005
Location: San Antonio Fl, Florida, USA
Model: 94SE 200000 miles
Posts: 10,957
Post imported post

Hello and Welcome . I am not up to speed on the 1800 . You should get some help shortly though . This is a large , diverse group of Goldwing lovers . I hope you enjoy the forums and visit often . Ride often , be safe ....its a traffic jungle out there .

Mike
NASSIR 1
NASSIR 6
NASSIR 7
NASSIR 8 in the works
OnaWingAndaPrayer is offline  
post #4 of 8 (permalink) Old 10-11-2009, 10:30 AM Thread Starter
Junior Member
 
Join Date: Oct 2009
Location: Pioneer, Louisiana, USA
Posts: 4
Post imported post

Thanks, Smeden,



I'll get on over to the workshop and give it a try...again!
Ridgeman is offline  
post #5 of 8 (permalink) Old 10-11-2009, 11:05 AM Thread Starter
Junior Member
 
Join Date: Oct 2009
Location: Pioneer, Louisiana, USA
Posts: 4
Post imported post

Well now, I have the 2 speaker wires disconnected! The main wiring connector next to the steering head is a handful of problems now...can't pull it apart...does anyone know where to press to release the lock on this connector?
Ridgeman is offline  
post #6 of 8 (permalink) Old 10-12-2009, 07:13 AM Thread Starter
Junior Member
 
Join Date: Oct 2009
Location: Pioneer, Louisiana, USA
Posts: 4
Post imported post

Well, finished that modification...but still need some additional help. I completed the left bar first. Just Perfect for me..up about 2 inches, back about an inch...then completed the right bar... but ....the right bar is lower than my left bar! and i'm certain that I followed the correct procedures! does anyone have any insight or suggestions?
Ridgeman is offline  
post #7 of 8 (permalink) Old 10-12-2009, 07:25 AM
Senior Member
 
DaveO430's Avatar
 
Join Date: Nov 2007
Location: Amity, Arkansas, USA
Model: GL1800 GL1100
Posts: 15,338
Garage
Post imported post

Be sure you got the wedge piece the same way on both sides. With my eyes I had to look at it carefully to see the difference in thickness.

Darksider #304 the force is strong in this one.
NRA endowment life member
Bright lights, protective gear and paying attention saves lives. Loud pipes just annoy the people behind you.
Wild Rhino Arkansas chapter
2010 1800 pearl yellow
2004 KLR650
DaveO430 is offline  
post #8 of 8 (permalink) Old 10-12-2009, 10:33 AM
Senior Member
 
SMEDEN(=the blacksmith)'s Avatar
 
Join Date: Sep 2009
Location: vordingborg, , Denmark
Model: GL1000 1975 K1+GL1800 2006 airbag(US-model).
Posts: 1,128
Post imported post

i see that you have found the lock tab. About these connectors - sometimes it is easier to take them apart when you first push them together and then pull , when you constantly apply pressure on the lock tab.

The winner is the man with most tools !
SMEDEN(=the blacksmith) is online now  
Reply

  Steve Saunders Goldwing Forums > Forums > Goldwing Technical Forum

Quick Reply
Message:
Options

Register Now



In order to be able to post messages on the Steve Saunders Goldwing Forums forums, you must first register.
Please enter your desired user name, your email address and other required details in the form below.

User Name:
Password
Please enter a password for your user account. Note that passwords are case-sensitive.

Password:


Confirm Password:
Email Address
Please enter a valid email address for yourself.

Email Address:
OR

Log-in









Human Verification

In order to verify that you are a human and not a spam bot, please enter the answer into the following box below based on the instructions contained in the graphic.



Thread Tools
Show Printable Version Show Printable Version
Email this Page Email this Page



Similar Threads
Thread Thread Starter Forum Replies Last Post
GL1100 Handlebar riser keithg64 For Sale/Wanted Forum 0 08-29-2010 10:24 PM
WTB Handlebar Riser For GL1100 soundaround123 For Sale/Wanted Forum 2 12-25-2009 02:32 PM
Handlebar Riser Kit English Bob For Sale/Wanted Forum 1 05-22-2009 11:09 PM
'83 GL1100A Riser / Setbacks dvjac Goldwing Technical Forum 3 03-02-2009 09:13 PM
Riser installation on GL1100 steveks Goldwing Technical Forum 13 07-13-2007 01:28 PM

Posting Rules  
You may post new threads
You may post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On

 
For the best viewing experience please update your browser to Google Chrome