Steve Saunders Goldwing Forums

Steve Saunders Goldwing Forums (https://www.goldwingfacts.com/forums/)
-   Reference and FAQ Forum (https://www.goldwingfacts.com/forums/10-reference-faq-forum/)
-   -   Building GL1800 and GL1500 Travel bags (https://www.goldwingfacts.com/forums/10-reference-faq-forum/346319-building-gl1800-gl1500-travel-bags.html)

skip20 05-03-2010 07:38 AM

imported post
 
I will be showing how to make the Travel Bags with the GL1800 Bags & center filler panel only.
Used 1/4" or 3/16" X 3" flat sheet for the braces mount.
You will need to make the cut to match the bag shape.
Drill & tap 2 holes each at 22 3/4" center to center.
Install using the stock bolts that came with the bike.
Using 2" X 2" x 1/8" square tubing drill the hole for the pin.
I used a center punch the fit the hole in the hitch to line them up.
Also drilled a 3/8" hole for the wiring to run inside the tubing.
Don't have the length set as yet.
Will be different between mount to Bike/Car or Trike.
You will need to open the Trike Trunk to get you helmet out at least.
You can weld the tubing on now being sure the bags are squared.
This will also help to keep them square as you move them around.

http://inlinethumb42.webshots.com/46...600x600Q85.jpg

Remove the 2 screws on the front inside as you will be cutting this area off.

http://inlinethumb51.webshots.com/43...600x600Q85.jpg

Cut the 2 side mount tabs off to get them out of the way.
Will also be cutting the top bag mount tab off.
Carefully cut the outside lip off using a 4" -4.5" cut off wheel on the grinder.
Then cut the inside lip off. You will be cutting the rubber seal off in the area.
Don't worry as it will be sealed when the new center floor in installed.
Carefully sand the lip smooth to bad inner & outer edge.
The dotted line in the picture shows where the floor will be mounted with pop rivets.
Check out the pictures.

Tools needed so far:
Drill & tap Home depot $8.00
Heavy Duty 4-1/2" Angle Grinder Harbor Freight $29.00 (on sale $19.95)
Package of 4.5" disc. Harbor Freight $15.00, comes with cut off, sanding & grinding disc.

http://inlinethumb58.webshots.com/22...600x600Q85.jpg

Next step will be to build the floor.
To be Cont.!

Since the floor for the GL1800 is fairly flat ( unlike the GL1500 ) with a curve in the front, I'm going to experiment using one layer of mat to shape it.
It should be flexible enough to trim to fit & make the curve
Using some Tile Board ( Home Depot ) lay one layer of 1.5oz mat and apply resin, roll it out & let cure.

http://inlinethumb39.webshots.com/80...600x600Q85.jpg

Make a card board patten of the floor to tranfer to the fiber glass sheet made.

http://inlinethumb63.webshots.com/17...600x600Q85.jpg

http://inlinethumb44.webshots.com/45...600x600Q85.jpg

OK, cut the floor shape out of the sheet of fiber glass.
I did it went it was gelling but not completely cure.
Slide it under the bag braces & tape it down & let it finish curing.

http://inlinethumb41.webshots.com/16...600x600Q85.jpg

http://inlinethumb39.webshots.com/46...600x600Q85.jpg

The single mat has harden but still a little bendeee.
Remove the masking tape which was holding it place.
Removed the top brace to be able to glass it easier.
Tape up the outside area with the plastic tape so the glass won't stick to it.
Laid 2 layers of 1 1/2oz mat on it & rolled it out.
Waiting dry time now

http://inlinethumb11.webshots.com/45...600x600Q85.jpg

The resin has dried so I removed it & cleaned up any boo boo's on the bags.
Trimmed the edges. & check for good fit, GREAT!
Will brace the outside of the floor as this is now the mold.
The floor will be part of the KIT if I get any looker or buyer
You can go ahead & rivet the floor to the bags.
Make sure the metal brace on on & the bags are square before doing that.
Check out the pictures for the nice fit.
The outside will be smooth.

http://inlinethumb23.webshots.com/47...600x600Q85.jpg

http://inlinethumb64.webshots.com/12...600x600Q85.jpg

http://inlinethumb22.webshots.com/38...600x600Q85.jpg

This morning I cut up some 2x4 for bracing of the floor.
Used the resin putty to attach & will lay 2 layers of mat around them.
Will also add some cross bracing
Doing this as I will be using this as a mold.

http://inlinethumb40.webshots.com/45...600x600Q85.jpg

Finished added the wood braces & fiber glassed them on to the floor panel.

http://inlinethumb02.webshots.com/51...600x600Q85.jpg

OK, so here's the mold for the floor.
Waxed it 5 times & spraying the release on it now.
May have a floor by this evening.

http://inlinethumb17.webshots.com/47...600x600Q85.jpg

Apply what I had left of the BLACK gel coat & it's now cured.
Laid 3 layers of 1.5oz mat & rolled it out.
It's now sitting out in the nice warm sun.

http://inlinethumb38.webshots.com/45...600x600Q85.jpg

The floor is finished.
Trimmed & Installed the floor with 3/16 Alum. pop rivets.
Install both metal braces & be sure to square the bags before you rivet.
Be sure to apply the silicone sealer on the ares in front where the bags were trimmed earlier.
Apply sealer along the back edge of the floor panel were it goes to the center filler panel.
After all rivets were in tight, apply sealer along all edges inside & out, smoothed with finger.
Also use whats on your finger & cover all rivets.
Will be making an "L" bracket which will mount off of the center reflector to the floor.
Will spray the bottom with rubber sealer to further help seal it.
There will be a vinyl bra snapped on to cover the front floor area.
This way no painting will be needed.
At this time you could make a vinyl cover for the top which can snap on, as on the "Tag-A-Long" bags.
I will be making a fiberglass hard top for it.

Addition tools needed:
Hand Riveter Set Harbor Freight $5.99 (on sale $4.99)
3/16" rivets box of 25 Home Depot $3.00
1 Tube of silicone sealer Home Depot $6.00
Clacking gun Home Depot $5.00
http://inlinethumb49.webshots.com/49...600x600Q85.jpg

Made a special License Plate for the Travel Bags, Can be made in assorted colors.
Think I was a little shaky on the close up 1st picture, need my AM coffee

http://inlinethumb08.webshots.com/45...600x600Q85.jpg

http://inlinethumb23.webshots.com/21...600x600Q85.jpg

FitzAl 05-03-2010 07:52 AM

imported post
 
That looks great. Do you have any pictures of it fitted?

skip20 05-03-2010 08:04 AM

imported post
 
This is the only bike with with a hitch right now.
It's sitting in the weeds right now

http://inlinethumb51.webshots.com/90...600x600Q85.jpg

http://inlinethumb61.webshots.com/79...600x600Q85.jpg

jwhitmore44 05-03-2010 08:22 AM

imported post
 
What a cool idea

rgbeard 05-03-2010 08:25 AM

imported post
 
What's the red car with the wire wheels in photo #1??

Lightin 05-03-2010 08:27 AM

imported post
 
looks Like MG

skip20 05-03-2010 08:28 AM

imported post
 
rgbeard wrote:
Quote:

What's the red car with the wire wheels in photo #1??
!973 Restored Spitfire.

Lightin 05-03-2010 08:29 AM

imported post
 
Well I wasnt even close

skip20 05-03-2010 08:33 AM

imported post
 
Lightin wrote:
Quote:

Well I wasnt even close
You were close, they are both English.

skip20 05-03-2010 09:10 AM

imported post
 
With the trike in the garage I got some newer picture of the Travel Bags.
1st pictures shows the GL1500 which will go with the trike when I sell it.

http://inlinethumb46.webshots.com/15...600x600Q85.jpg

http://inlinethumb29.webshots.com/17...600x600Q85.jpg

http://inlinethumb11.webshots.com/47...600x600Q85.jpg

2nd pictures shows the GL1800 Travel Bag before I made the lid.

http://inlinethumb10.webshots.com/12...600x600Q85.jpg

http://inlinethumb30.webshots.com/44...600x600Q85.jpg


All times are GMT -5. The time now is 12:11 PM.

Powered by vBulletin® Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.

User Alert System provided by Advanced User Tagging (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Shoutbox provided by vBShout v6.2.1 (Lite) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd. Runs best on HiVelocity Hosting.

 
For the best viewing experience please update your browser to Google Chrome