Steve Saunders Goldwing Forums

Steve Saunders Goldwing Forums (https://www.goldwingfacts.com/forums/)
-   Goldwing Technical Forum (https://www.goldwingfacts.com/forums/2-goldwing-technical-forum/)
-   -   Stainless brake lines for 1500 (https://www.goldwingfacts.com/forums/2-goldwing-technical-forum/666103-stainless-brake-lines-1500-a.html)

toolcraft4100 01-16-2019 08:46 PM

Stainless brake lines for 1500
 
I'm going to replace the original brake lines on my '91 Goldwing. The first decision might be to decide whether or not to replace the short little hose under the tank. The website I've been looking at says it is not necessary and sells it separately. I've never seen this hose and I don't know where it fits in the system. I'm interested to know if others of you have replaced this little hose or not.

BLUTHUNDR31 01-16-2019 08:52 PM

I might be wrong, but I did NOT change that hose. If its the one I'm thinking of, it goes from the rear master cylinder to the front brake line, , but the SS brake lines that I put in only went from the front caliper to the "connector" end of that hose. It wouldn't reach the master cylinder so I took that as a "sign-from-God" to leave it alone.

AZgl1800 01-16-2019 10:50 PM

I replaced ALL of them.


the foot pedal went from dangerously sloppy, to hard stop immediately.

BLUTHUNDR31 01-17-2019 03:12 AM

Could that short hose have a "shell" (plastic) covering it to protect it and keep it from rubbing on the tank and/or frame? I don't think that short hose came in the "kit" I got either, , ,I don't have any SS hoses left over, , , and I'm sure I didn't change the short one.

OnaWingAndaPrayer 01-17-2019 05:52 AM

The short hose I recall is mounted just about centerline of the bike . It attaches to the frame just above the front of the swingarm and makes a 90* turn to mouint on the left front of the swingarm. It is about 5" long. Memory tells me it was a bit aggravating to install.
But consider this .... unless you replace all the lines the system is no better than the weakest part. One soft expanding hose still leaves you with a place for the pressure to expand and not exert force on the calipers.

toolcraft4100 01-17-2019 10:02 AM

short hose
 
I've got the 3-hose set, the short hose and the clutch hose in my wish list on the randakk cycle shakk website. I just need to move them to my cart and make it happen.

Is it really important to prefill the hoses before installation? Is there a trick to that?

snowmoer 01-17-2019 10:10 AM

The rear braded hose that I got eliminated that short hose. Mine goes directly from the master cylinder to the rear caliper.

I did not pre fill my hoses. I use a vac when I change fluid. I just used that and it sucked all the air out of the line.

ALEX BERECZKY 01-17-2019 02:31 PM

I replaced All my brake and clutch lines 100%... each line is a custom-made single length of Braided Stainless
I've done this on 2 GL1500's so far, and developed a kit with "Techna-Fit" because I could not find one of that design elsewhere:

With the new lines I only need to bleed the brakes every 2yrs... rather than every couple months previously; I presume the stock lines bleed air through the multiple fittings.



Techna-Fit, Inc.
493B Southpoint Circle
Brownsburg, IN 46112
317-350-2153
[email protected]


ps: I have an extra Rear Line, in case you're interested... Send PM

toolcraft4100 01-18-2019 08:53 AM

Quote:

Originally Posted by ALEX BERECZKY (Post 5816093)
I replaced All my brake and clutch lines 100%... each line is a custom-made single length of Braided Stainless
I've done this on 2 GL1500's so far, and developed a kit with "Techna-Fit" because I could not find one of that design elsewhere:

With the new lines I only need to bleed the brakes every 2yrs... rather than every couple months previously; I presume the stock lines bleed air through the multiple fittings.



Techna-Fit, Inc.
493B Southpoint Circle
Brownsburg, IN 46112
317-350-2153
[email protected]


ps: I have an extra Rear Line, in case you're interested... Send PM

Alex, the accounts manager from Techna-Fit replied that they could not find what they made for you and asked me to send him the old lines so they can copy them. I would rather have the new lines in hand before I begin the project. So I appreciate your help and I may take you up on the rear hose. Are you saying that you have one hose that goes from the RMC to the rear caliper. And that it replaces the two OEM hoses and the OEm pipe that goes between them?

toolcraft4100 01-18-2019 09:07 AM

research...
 
I've been reading old threads on this forum and studying the parts fisch. I certainly intend to replace all the rubber hoses. I am starting to understand that a popular method is to replace the hose-pipe-hose between the RMC and the rear caliper with one hose. This seems to make good sense. Why not replace the entire assembly from the RMC to the front caliper with one hose?


When I bleed the new hoses do I need a "mitey-vac" or something similar or can I use the Harbor Freight manual vacuum pump? Prefilling the hoses seems like it would make a mess. I'm not afraid of messes, but I try to avoid brake fluid messes and it seems like a vacuum should pull all the air out regardless of how much there is.


All times are GMT -5. The time now is 12:02 AM.

Powered by vBulletin® Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.

User Alert System provided by Advanced User Tagging (Pro) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd.
Shoutbox provided by vBShout v6.2.1 (Lite) - vBulletin Mods & Addons Copyright © 2019 DragonByte Technologies Ltd. Runs best on HiVelocity Hosting.

 
For the best viewing experience please update your browser to Google Chrome