Steve Saunders Goldwing Forums - Search Results

Advanced Search
Showing results 1 to 25 of 70
Search took 0.29 seconds.
Search: Posts Made By: Sprocketrocket55
Forum: Goldwing Technical Forum   10-13-2019, 10:32 PM
Replies: 17
Views: 374
Posted By Sprocketrocket55
To release a stuck clutch: If you have good...

To release a stuck clutch: If you have good clutch pressure on the handlebar lever, put it on the center stand start it in gear rev up a bit and slam on the rear brake with the lever pulled in
...
Forum: Goldwing Technical Forum   10-13-2019, 10:24 PM
Replies: 12
Views: 496
Posted By Sprocketrocket55
I have one and put my 1985 gl1200 on it. Had no...

I have one and put my 1985 gl1200 on it. Had no problem. You can find a coupon in the ads for 20 or 25 percent off. I think I paid $250 with coupons.

Sent from my SM-J320V using Tapatalk
Forum: Goldwing Technical Forum   10-13-2019, 10:29 AM
Replies: 15
Views: 211
Posted By Sprocketrocket55
Could also be loose studs on the spline assembly...

Could also be loose studs on the spline assembly or worn dampers that the studs go into.

Sent from my SM-J320V using Tapatalk
Forum: Goldwing Technical Forum   10-11-2019, 04:30 PM
Replies: 25
Views: 888
Posted By Sprocketrocket55
I use Yamaha fuel tank rust remover and a...

I use Yamaha fuel tank rust remover and a handfull of bolts to shake around. Count the bolts to make sure one doesn't get caught somewhere.
Part 2 of the kit neutralizes a rustproofs.

Sent from...
Forum: Goldwing Technical Forum   10-11-2019, 04:25 PM
Replies: 21
Views: 720
Posted By Sprocketrocket55
I would use some paint stripper first then polish...

I would use some paint stripper first then polish and recoat

Sent from my SM-J320V using Tapatalk
Forum: Goldwing Technical Forum   09-10-2019, 08:49 PM
Replies: 18
Views: 594
Posted By Sprocketrocket55
You didn't say the model year Sent from my...

You didn't say the model year

Sent from my SM-J320V using Tapatalk
Forum: Goldwing Technical Forum   09-10-2019, 08:18 PM
Replies: 18
Views: 594
Posted By Sprocketrocket55
I would check for a fouled plug first Sent...

I would check for a fouled plug first

Sent from my SM-J320V using Tapatalk
Forum: Goldwing Technical Forum   09-09-2019, 11:55 AM
Replies: 5
Views: 164
Posted By Sprocketrocket55
There may have been a ignition switch recall back...

There may have been a ignition switch recall back in the day on those bikes I vaguely remember something like that

Sent from my SM-J320V using Tapatalk
Forum: Goldwing Technical Forum   08-26-2019, 10:37 PM
Replies: 17
Views: 558
Posted By Sprocketrocket55
You can carve foam with a electric knife. A T50...

You can carve foam with a electric knife. A T50 hand stapler with a stiff spring.

Sent from my SM-J320V using Tapatalk
Forum: Goldwing Technical Forum   08-17-2019, 12:20 AM
Replies: 9
Views: 263
Posted By Sprocketrocket55
No real torque spec. Just tighten normally, I...

No real torque spec. Just tighten normally, I use a 1/4 inch ratchet

Sent from my SM-J320V using Tapatalk
Forum: Goldwing Technical Forum   08-12-2019, 11:12 PM
Replies: 30
Views: 2,006
Posted By Sprocketrocket55
I say no. Rubber loses solvents and dries out....

I say no. Rubber loses solvents and dries out. Thats why rubber smells like.... rubber. Tires expire for that reason. Bent valves are $$$

Sent from my SM-J320V using Tapatalk
Forum: Goldwing Technical Forum   08-10-2019, 11:28 AM
Replies: 5
Views: 260
Posted By Sprocketrocket55
Why would you have to mess with a driveshaft to...

Why would you have to mess with a driveshaft to replace a tire? You should be able to pull the boot back to inspect thr seal.

Sent from my SM-J320V using Tapatalk
Forum: Goldwing Technical Forum   08-06-2019, 06:38 AM
Replies: 3
Views: 178
Posted By Sprocketrocket55
Book says remove the master cylinder bolts then...

Book says remove the master cylinder bolts then the lines

Sent from my SM-J320V using Tapatalk
Forum: Goldwing Technical Forum   08-06-2019, 06:26 AM
Replies: 47
Views: 1,710
Posted By Sprocketrocket55
To change brake/clutch fluid I suck or sop all...

To change brake/clutch fluid I suck or sop all the old fluid from the master cylinder, then ad some fresh fluid pump the handle/pedal to get the gunk out of the cylinder, sop out the fluid again and...
Forum: Goldwing Technical Forum   08-05-2019, 05:08 PM
Replies: 47
Views: 1,710
Posted By Sprocketrocket55
Get this manual on...

Get this manual on ebayhttps://uploads.tapatalk-cdn.com/20190805/676ea264d965e6a9c1dfb94db2a33bbf.jpg

Sent from my SM-J320V using Tapatalk
Forum: Goldwing Technical Forum   08-05-2019, 04:28 PM
Replies: 25
Views: 1,473
Posted By Sprocketrocket55
Caliper piston is usually the problem. I had to...

Caliper piston is usually the problem. I had to make a scraper tool out of an old spoke. Bent and Flattened the end. Ground it to the right shape to reach every part of the seals groove. It has to be...
Forum: Goldwing Technical Forum   08-04-2019, 01:27 AM
Replies: 47
Views: 1,710
Posted By Sprocketrocket55
Definitely a least look at the belts. Remove the...

Definitely a least look at the belts. Remove the 2 bolts at the bottom hose fitting and drain anti freeze then the two on the bottom of the radiator. Swing radiator out to get the inner bolts out of...
Forum: Goldwing Technical Forum   07-29-2019, 08:58 PM
Replies: 12
Views: 834
Posted By Sprocketrocket55
If you can get any lock off of the bike take it...

If you can get any lock off of the bike take it to a locksmith, he can make a key

Sent from my SM-J320V using Tapatalk
Forum: Goldwing Technical Forum   07-22-2019, 11:12 AM
Replies: 53
Views: 1,907
Posted By Sprocketrocket55
If you have a trailer to put ot on or a lift: ...

If you have a trailer to put ot on or a lift:
Use center stand and strap it so it can't fold up. Drag the bike back to hang the rear wheel in mid air and strap the bike down.

Sent from my...
Forum: Goldwing Technical Forum   07-12-2019, 11:29 AM
Replies: 7
Views: 289
Posted By Sprocketrocket55
Gasgacinch is like weatherstriping glue, except...

Gasgacinch is like weatherstriping glue, except it is meant to use on gaskets. Just dab it on lightly on both the part and the gasket let dry and install. It will not glue it permanently.

Sent...
Forum: Goldwing Technical Forum   06-25-2019, 06:42 PM
Replies: 4
Views: 181
Posted By Sprocketrocket55
There is s plug on the stator/flywheel housing,...

There is s plug on the stator/flywheel housing, remove and use a socket wrench to rotate it

Sent from my SM-J320V using Tapatalk
Forum: Goldwing Technical Forum   06-15-2019, 11:42 PM
Replies: 4
Views: 215
Posted By Sprocketrocket55
Step 4 is checking for ground on the handlebar...

Step 4 is checking for ground on the handlebar switch

Sent from my SM-J320V using Tapatalk
Forum: Goldwing Technical Forum   06-15-2019, 11:31 PM
Replies: 4
Views: 215
Posted By Sprocketrocket55
Flow chart for turn...

Flow chart for turn signalshttps://uploads.tapatalk-cdn.com/20190616/442b97ebc43cb2084a1265558d3e1a79.jpg

Sent from my SM-J320V using Tapatalk
Forum: Goldwing Technical Forum   06-09-2019, 01:24 PM
Replies: 14
  Tires
Views: 677
Posted By Sprocketrocket55
The bump should smooth out. I like OEM tires ...

The bump should smooth out. I like OEM tires

Sent from my SM-J320V using Tapatalk
Forum: Goldwing Technical Forum   06-06-2019, 02:55 PM
Replies: 13
Views: 485
Posted By Sprocketrocket55
Possibly the drain for the air filter box ...

Possibly the drain for the air filter box

Sent from my SM-J320V using Tapatalk
Showing results 1 to 25 of 70

 
Forum Jump
 
For the best viewing experience please update your browser to Google Chrome